Pump it up mod#
Pump it up software#
Pump it up code#

I traced a set of PIU arrows I found online, sized them correctly, and had them professionally printed and laminated. It’s set up in such a way that the pins read low when the pad is not engaged and high when engaged.įor the finish, I coated the frame and top half of the pads in a layer of black spray paint.

Pump it up code#

If you want to see this code for yourself or want any tips/pointers, feel free to email me. This mapping is then mirrored on StepF2’s key settings to complete the setup. Each of the 5 pads is assigned a pin on the Arduino Leonardo and whenever a change in state is observed, a signal is sent to the connected keyboard that signifies either a key press or release on a keyboard.

Pump it up software#

The software side of this project is incredibly simple. A single pad is shown at the top of the pad to demonstrate what the connecting sheet looks like. You can see the interlocking pattern of aluminum present. Cat 5 was used to wire everything together, with heavy duty staples being used to fasten it in place with the aluminum and hot glue elsewhere. High density foam was laid around the platform (there is an inch space between the platform and 1/2″ support piece) and functioned as a sort of spring mechanism to keep the pad above the sheet in its natural state. When the pad is pressed, the strip underneath the pad itself connects the two halves of aluminum sheet, completing the circuit and causing a change of state for the pin on the Arduino. Underneath the pad itself is a single strip of aluminum. One of these halves is connected to power and the other is connected to a corresponding pin on the Arduino. Essentially, underneath each 1/4″ pad is a 1/4″ platform with a sheet of interlocking foil on it acting as a conductor (2 separate halves). The mechanism is simple and rather easy to understand. Next came designing the mechanism for the pressure sensors to determine when the pad is pressed. Again, 1/2″ plywood was used as spacers between the pads which resulted in a sort of frame for each pad. The entirety of the pad is rested on a sheet of 35″x35″x1/2″ plywood acting as a base, with 1″ strips of 1/2″ plywood going around the sides of the base to act as a frame. An Arduino Leonardo was used as the computer (chosen over other options due to its ability to be plugged into a computer and function as a keyboard).įirst came building the frame.

Other than that, I ended up using an 8mm (just over 1/4″) high density foam to act as a spring for the pad (mechanism will be explained later) and some Cat5 to wire everything up.

To add a layer of protection (for both the wood and the feet of those who are playing), the top is covered in a layer of 1/32″ polycarbonate plastic.

I tried to stay as true to the original dimensions of the pad as possible, which resulted in overall dimensions of 35″x35″x1″ (which just barely fits in the trunk of my 2006 Prius, let me just add). Eventually I just settled on 1/2″ plywood for base/support and 1/4″ birch sheets to use for the pads and pad platforms. I wanted this to be fairly lightweight to ease portability (mainly from home to school) but also look decent. I was able to build mine for about $175-200, saving a fair bit of money.įirst came deciding on what materials I wanted to use for the build. Decent pads can be anywhere from $300-500 depending on manufacturer. Plus, the market for professionally made pads is somewhat barren, meaning I’d have to wait for quite a bit and spend a small fortune if I wanted to buy a decent pad instead of building my own.

Pump it up mod#

D&B) supporting the brand as well.Ī Pump it Up: Prime 2 machine (most recent iteration).Īs the closest machine is 45 minutes away from where I’m staying at Virginia Tech next year (and honestly 30 minutes away from my house in Atlanta on a good day), I decided to try my hand at building my own dance pad to hook up with a computer and play with StepF2, a mod for Stepmania that emulates a version of PIU. You’ll likely find machines for the game at local arcades, with several big names (i.e. For those who don’t know what it is, PIU (owned by Andamiro) is essentially a Korean version of Konami’s Dance Dance Revolution, with arrows in the corners and middle instead of the cardinal directions. Recently, through influence of friends and a bit of chance, I’ve become interested in the dance game Pump it Up (PIU).